Coils and Coil Springs

King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing. King Springs was established in 1956 on Queensland's Gold Coast. Our complex comprises three adjoining factories spanning 8000 square metres. Administration, manufacturing and warehousing all function from this one location employing over 70 people.   All King Springs are CAD designed Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging. Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections. Gas heating is used for the furnaces for their clean and efficient heating All coils are made with a computer controlled process for precise tolerances Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness. the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface Dipped in phosphate for corrosion protection Epoxy powder coated for a durable finish and presentation  

King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing. King Springs was established in 1956 on Queensland's Gold Coast. Our complex comprises three adjoining factories spanning 8000 square metres. Administration, manufacturing and warehousing all function from this one location employing over 70 people.   All King Springs are CAD designed Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging. Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections. Gas heating is used for the furnaces for their clean and efficient heating All coils are made with a computer controlled process for precise tolerances Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness. the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface Dipped in phosphate for corrosion protection Epoxy powder coated for a durable finish and presentation  

King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing. King Springs was established in 1956 on Queensland's Gold Coast. Our complex comprises three adjoining factories spanning 8000 square metres. Administration, manufacturing and warehousing all function from this one location employing over 70 people.   All King Springs are CAD designed Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging. Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections. Gas heating is used for the furnaces for their clean and efficient heating All coils are made with a computer controlled process for precise tolerances Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness. the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface Dipped in phosphate for corrosion protection Epoxy powder coated for a durable finish and presentation  

King Springs leads the way in the design and manufacture of advanced progressive springs with both variable pitch and tapered wire forms. King Springs service all sectors of the automotive market including passenger, commercial and Four Wheel Drive vehicles and various Motorsport categories including circuit, rally, speedway and off-road racing. King Springs was established in 1956 on Queensland's Gold Coast. Our complex comprises three adjoining factories spanning 8000 square metres. Administration, manufacturing and warehousing all function from this one location employing over 70 people.   All King Springs are CAD designed Only X5K Material is used, this is a new generation of high strength Spring Steel which with-stands higher operating stresses and has superior resistance to sagging. Peeling & Tapering - Bar peeling and tapering of 1mm from the surface removes all imperfections. Gas heating is used for the furnaces for their clean and efficient heating All coils are made with a computer controlled process for precise tolerances Once the coil has been rolled it is placed into an oil quenching bath at 850 degrees Celsius and hardened to 62 HRC Rockwell Hardness. the coil is then tempered in an oven at 400 degrees Celsius and is tempered to 54 HRC If the coil requires a flat seat it is the ground to suit in a computer controlled wet grinder The coil si then shot peened to stress relieve the outer surface for a uniformed finish and optimal power coat surface Dipped in phosphate for corrosion protection Epoxy powder coated for a durable finish and presentation  

Carbon Offroad Coilover Coil Springs Carbon's professionally engineered progressive rate coil springs were specifically designed here in Australia and offer an improved ride quality over the factory spring on your 4x4. The natural progression of this design is to be tough enough with increased rates designed for additional accessory loads and still maintain a driver friendly feel.  The Carbon Coil Springs are designed to work with the range of Carbon MT2.0 Struts. What makes the Carbon Coil Spring better than other springs on the market? Our  focus on the Carbon Coil Spring was to deliver to the market a suspension system that is comfortable on road and can handle additional accessory loads and improve the vehicle on road handling, then while offroad with increases with travel and improved articulation, this has been done by utilising our own custom progresive rate coil design specifically to suit 4wd's alike. Driving comfort never felt so good. Designed to offer you a smooth riding experience, the Carbon 4x4 Coil Springs takes an already great product and makes it even better. The special formulated spring steel used resists fatigue and sagging and is powder coated for protection against the elements for longevity. The linear rate elements with these coils, ensures reliable performance. Large bumps in the road will be soaked up without transmitting that force to your chassis thanks to its unequaled ability to flex evenly and uniformly under load. If you want the ride you deserve, upgrade to a set of Carbon Coil Springs for your 4wd.   Manufacturing processes - - Manufactured from high grade carbon spring steel.  - CNC mandrel bent for a precise manufacturing process.  - Each spring is scragged (compressed to coil bind to set the spring height) - The outer surface of the coil is blasted with steel bearings to relieve the surface tension for a uniformed finish. - Powder coated for protection from rust and corrosion. - Each coil is checked ensuring a high level of quality control. - For universal coil over applications, both ends are ground flat for an even mating surface.   14 inch free height  linear rate design 0-70kg constant load on front end of most dual cabs flat ground ends 3.0 inch inside diameter, will work on Carbon MT2.0 coilovers, Fox 2.0 IFP coilovers. Fox 2.5 series coilovers, King 2.5 coilovers, Radflo 2.5 coilovers, Icon 2.5 coilovers and any other brand that takes a 3 inch ID coilover spring.  

Front flat ground coilover coil, linear rate 750lb/in. SOLD EACH 

Carbon Offroad Progressive Rate Coilover Coil Springs Carbon's professionally engineered linear rate coil springs were specifically designed here in Australia and offer an improved ride quality over the factory spring on your 4x4.  The Carbon Coil Springs are designed to work with the range of Carbon 2.0 and 2.5 Struts. They also work with other coilover brands such as King, Fox, Icon, Raflo, Superior and more. What makes the Carbon Coil Spring better than other springs on the market? Our  focus on the Carbon Coil Spring was to deliver to the market a suspension system that is comfortable on road and can handle additional accessory loads and improve the vehicle on road handling, then while offroad with increases with travel and improved articulation, this has been done by utilising a choice of linear rate coil designs specifically to suit 4wd's alike. Driving comfort never felt so good. Designed to offer you a smooth riding experience, the Carbon 4x4 Coil Springs takes an already great product and makes it even better. The special formulated spring steel used resists fatigue and sagging and is powder coated for protection against the elements for longevity. The linear rate elements with these coils, ensures large bumps in the road will be soaked up without transmitting that force to your chassis thanks to its unequaled ability to flex evenly and uniformly under load. The rate choice allows you to tailor the spring to your driving style and accessory load. If you want the ride you deserve, upgrade to a set of Carbon Linear Rate Coil Springs for your 4wd.   Manufacturing processes - - Manufactured from high grade carbon spring steel.  - CNC mandrel bent for a precise manufacturing process.  - Each spring is scragged (compressed to coil bind to set the spring height) - The outer surface of the coil is blasted with steel bearings to relieve the surface tension for a uniformed finish. - Powder coated for protection from rust and corrosion. - Each coil is checked ensuring a high level of quality control. - For universal coil over applications, both ends are ground flat for an even mating surface.   12 inch free height  linear rate design 70-130kg constant load on front end of most dual cabs - 750lb/inch rate - suited for heavier rigs like LC200 coilovers flat ground ends 3.0 inch inside diameter, will work on Carbon MT2.0 coilovers, Fox 2.0 IFP coilovers. Fox 2.5 series coilovers, King 2.5 coilovers, Radflo 2.5 coilovers, Icon 2.5 coilovers and any other brand that takes a 3 inch ID coilover spring.   Front flat ground coilover coil, linear rate 750lb/in.

Carbon Offroad Progressive Rate Coilover Coil Springs Carbon's professionally engineered progressive rate coil springs were specifically designed here in Australia and offer an improved ride quality over the factory spring on your 4x4. The natural progression of this design is to be tough enough with increased rates designed for additional accessory loads and still maintain a driver friendly feel.  The Carbon Coil Springs are designed to work with the range of Carbon MT2.0 Struts. What makes the Carbon Coil Spring better than other springs on the market? Our  focus on the Carbon Coil Spring was to deliver to the market a suspension system that is comfortable on road and can handle additional accessory loads and improve the vehicle on road handling, then while offroad with increases with travel and improved articulation, this has been done by utilising our own custom progresive rate coil design specifically to suit 4wd's alike. Driving comfort never felt so good. Designed to offer you a smooth riding experience, the Carbon 4x4 Coil Springs takes an already great product and makes it even better. The special formulated spring steel used resists fatigue and sagging and is powder coated for protection against the elements for longevity. The progressive rate elements with these coils, ensures large bumps in the road will be soaked up without transmitting that force to your chassis thanks to its unequaled ability to flex evenly and uniformly under load. These are not your typical progressive rate coil springs! If you want the ride you deserve, upgrade to a set of Carbon Progressive Rate Coil Springs for your 4wd.   Manufacturing processes - - Manufactured from high grade carbon spring steel.  - CNC mandrel bent for a precise manufacturing process.  - Each spring is scragged (compressed to coil bind to set the spring height) - The outer surface of the coil is blasted with steel bearings to relieve the surface tension for a uniformed finish. - Powder coated for protection from rust and corrosion. - Each coil is checked ensuring a high level of quality control. - For universal coil over applications, both ends are ground flat for an even mating surface.   14 inch free height  progressive rate design 70-130kg constant load on front end of most dual cabs flat ground ends 3.0 inch inside diameter, will work on Carbon MT2.0 coilovers, Fox 2.0 IFP coilovers. Fox 2.5 series coilovers, King 2.5 coilovers, Radflo 2.5 coilovers, Icon 2.5 coilovers and any other brand that takes a 3 inch ID coilover spring.   Carbon Offroad 3.0 inch ID, 14 inch, progressive rate coilover coil spring 70-130kg load PAIR

Carbon Offroad Progressive Rate Coilover Coil Springs Carbon's professionally engineered progressive rate coil springs were specifically designed here in Australia and offer an improved ride quality over the factory spring on your 4x4. The natural progression of this design is to be tough enough with increased rates designed for additional accessory loads and still maintain a driver friendly feel.  The Carbon Coil Springs are designed to work with the range of Carbon MT2.0 Struts. What makes the Carbon Coil Spring better than other springs on the market? Our  focus on the Carbon Coil Spring was to deliver to the market a suspension system that is comfortable on road and can handle additional accessory loads and improve the vehicle on road handling, then while offroad with increases with travel and improved articulation, this has been done by utilising our own custom progresive rate coil design specifically to suit 4wd's alike. Driving comfort never felt so good. Designed to offer you a smooth riding experience, the Carbon 4x4 Coil Springs takes an already great product and makes it even better. The special formulated spring steel used resists fatigue and sagging and is powder coated for protection against the elements for longevity. The progressive rate elements with these coils, ensures large bumps in the road will be soaked up without transmitting that force to your chassis thanks to its unequaled ability to flex evenly and uniformly under load. These are not your typical progressive rate coil springs! If you want the ride you deserve, upgrade to a set of Carbon Progressive Rate Coil Springs for your 4wd.   Manufacturing processes - - Manufactured from high grade carbon spring steel.  - CNC mandrel bent for a precise manufacturing process.  - Each spring is scragged (compressed to coil bind to set the spring height) - The outer surface of the coil is blasted with steel bearings to relieve the surface tension for a uniformed finish. - Powder coated for protection from rust and corrosion. - Each coil is checked ensuring a high level of quality control. - For universal coil over applications, both ends are ground flat for an even mating surface.   14 inch free height  progressive rate design 70-130kg constant load on front end of most dual cabs flat ground ends 3.0 inch inside diameter, will work on Carbon MT2.0 coilovers, Fox 2.0 IFP coilovers. Fox 2.5 series coilovers, King 2.5 coilovers, Radflo 2.5 coilovers, Icon 2.5 coilovers and any other brand that takes a 3 inch ID coilover spring.  

Carbon Offroad Progressive Rate Coilover Coil Springs Carbon's professionally engineered progressive rate coil springs were specifically designed here in Australia and offer an improved ride quality over the factory spring on your 4x4. The natural progression of this design is to be tough enough with increased rates designed for additional accessory loads and still maintain a driver friendly feel.  The Carbon Coil Springs are designed to work with the range of Carbon MT2.0 Struts. What makes the Carbon Coil Spring better than other springs on the market? Our  focus on the Carbon Coil Spring was to deliver to the market a suspension system that is comfortable on road and can handle additional accessory loads and improve the vehicle on road handling, then while offroad with increases with travel and improved articulation, this has been done by utilising our own custom progresive rate coil design specifically to suit 4wd's alike. Driving comfort never felt so good. Designed to offer you a smooth riding experience, the Carbon 4x4 Coil Springs takes an already great product and makes it even better. The special formulated spring steel used resists fatigue and sagging and is powder coated for protection against the elements for longevity. The progressive rate elements with these coils, ensures large bumps in the road will be soaked up without transmitting that force to your chassis thanks to its unequaled ability to flex evenly and uniformly under load. These are not your typical progressive rate coil springs! If you want the ride you deserve, upgrade to a set of Carbon Progressive Rate Coil Springs for your 4wd.   Manufacturing processes - - Manufactured from high grade carbon spring steel.  - CNC mandrel bent for a precise manufacturing process.  - Each spring is scragged (compressed to coil bind to set the spring height) - The outer surface of the coil is blasted with steel bearings to relieve the surface tension for a uniformed finish. - Powder coated for protection from rust and corrosion. - Each coil is checked ensuring a high level of quality control. - For universal coil over applications, both ends are ground flat for an even mating surface.   14 inch free height  progressive rate design 40-80kg constant load on front end of most dual cabs flat ground ends 3.0 inch inside diameter, will work on Carbon MT2.0 coilovers, Fox 2.0 IFP coilovers. Fox 2.5 series coilovers, King 2.5 coilovers, Radflo 2.5 coilovers, Icon 2.5 coilovers and any other brand that takes a 3 inch ID coilover spring.  

Carbon Offroad Progressive Rate Coilover Coil Springs Carbon's professionally engineered progressive rate coil springs were specifically designed here in Australia and offer an improved ride quality over the factory spring on your 4x4. The natural progression of this design is to be tough enough with increased rates designed for additional accessory loads and still maintain a driver friendly feel.  The Carbon Coil Springs are designed to work with the range of Carbon MT2.0 Struts. What makes the Carbon Coil Spring better than other springs on the market? Our  focus on the Carbon Coil Spring was to deliver to the market a suspension system that is comfortable on road and can handle additional accessory loads and improve the vehicle on road handling, then while offroad with increases with travel and improved articulation, this has been done by utilising our own custom progresive rate coil design specifically to suit 4wd's alike. Driving comfort never felt so good. Designed to offer you a smooth riding experience, the Carbon 4x4 Coil Springs takes an already great product and makes it even better. The special formulated spring steel used resists fatigue and sagging and is powder coated for protection against the elements for longevity. The progressive rate elements with these coils, ensures large bumps in the road will be soaked up without transmitting that force to your chassis thanks to its unequaled ability to flex evenly and uniformly under load. These are not your typical progressive rate coil springs! If you want the ride you deserve, upgrade to a set of Carbon Progressive Rate Coil Springs for your 4wd.   Manufacturing processes - - Manufactured from high grade carbon spring steel.  - CNC mandrel bent for a precise manufacturing process.  - Each spring is scragged (compressed to coil bind to set the spring height) - The outer surface of the coil is blasted with steel bearings to relieve the surface tension for a uniformed finish. - Powder coated for protection from rust and corrosion. - Each coil is checked ensuring a high level of quality control. - For universal coil over applications, both ends are ground flat for an even mating surface.   12 inch free height  progressive rate design 70-130kg constant load on front end of most dual cabs flat ground ends 3.0 inch inside diameter, will work on Carbon MT2.0 coilovers, Fox 2.0 IFP coilovers. Fox 2.5 series coilovers, King 2.5 coilovers, Radflo 2.5 coilovers, Icon 2.5 coilovers and any other brand that takes a 3 inch ID coilover spring.  

Carbon Offroad Progressive Rate Coilover Coil Springs Carbon's professionally engineered progressive rate coil springs were specifically designed here in Australia and offer an improved ride quality over the factory spring on your 4x4. The natural progression of this design is to be tough enough with increased rates designed for additional accessory loads and still maintain a driver friendly feel.  The Carbon Coil Springs are designed to work with the range of Carbon MT2.0 Struts. What makes the Carbon Coil Spring better than other springs on the market? Our  focus on the Carbon Coil Spring was to deliver to the market a suspension system that is comfortable on road and can handle additional accessory loads and improve the vehicle on road handling, then while offroad with increases with travel and improved articulation, this has been done by utilising our own custom progresive rate coil design specifically to suit 4wd's alike. Driving comfort never felt so good. Designed to offer you a smooth riding experience, the Carbon 4x4 Coil Springs takes an already great product and makes it even better. The special formulated spring steel used resists fatigue and sagging and is powder coated for protection against the elements for longevity. The progressive rate elements with these coils, ensures large bumps in the road will be soaked up without transmitting that force to your chassis thanks to its unequaled ability to flex evenly and uniformly under load. These are not your typical progressive rate coil springs! If you want the ride you deserve, upgrade to a set of Carbon Progressive Rate Coil Springs for your 4wd.   Manufacturing processes - - Manufactured from high grade carbon spring steel.  - CNC mandrel bent for a precise manufacturing process.  - Each spring is scragged (compressed to coil bind to set the spring height) - The outer surface of the coil is blasted with steel bearings to relieve the surface tension for a uniformed finish. - Powder coated for protection from rust and corrosion. - Each coil is checked ensuring a high level of quality control. - For universal coil over applications, both ends are ground flat for an even mating surface.   12 inch free height  progressive rate design 70-130kg constant load on front end of most dual cabs flat ground ends 3.0 inch inside diameter, will work on Carbon MT2.0 coilovers, Fox 2.0 IFP coilovers. Fox 2.5 series coilovers, King 2.5 coilovers, Radflo 2.5 coilovers, Icon 2.5 coilovers and any other brand that takes a 3 inch ID coilover spring.